Showing posts with label dimplex heaters. Show all posts
Showing posts with label dimplex heaters. Show all posts

Wednesday, December 10, 2014

Reviews of 32,000 BTU Variable CSA Certified Propane Tank Top Heater

32,000 BTU Variable CSA Certified Propane Tank Top Heater
Customer Ratings: 4.5 stars
List Price: $99.99
Sale Price: $70.12
Today's Bonus: 30% Off
Buy Now

I like this heater. I have a table top propane heater and this heater puts out 3 times more heat and starts up almost immediately. The only down fault I have with this heater, is it does not look that great. Looks to much like a commercial tool instead of something you would like to see on your patio. Could try and conceal some of the wiring.

Click Here For Most Helpful Customer Reviews >>

This was just the ticket on my last hunt. Still snow on the ground and I never got the least bit cole.

Best Deals on 32,000 BTU Variable CSA Certified Propane Tank Top Heater

This is a great little heater. It puts off good heat directly in front of it, but a lot of heat escapes up. So it works great in my patio that is covered, but fair to ok out in the courtyard. The craftsmanship it self is simple and light weight. I would not say it is delicate, but all the components are light weight and not designed to withstand major abuse. It is easy to use, but would be awesome if it had click starters instead of using a long lighter. I have only used it a handful of times, but I would recommend it so far.

Honest reviews on 32,000 BTU Variable CSA Certified Propane Tank Top Heater

Easy to install on tank; fairly easy to light; just don't have your hair in the line of fire! :-) Throws out a lot of heat.

Buy Fom Amazon Now

Friday, October 17, 2014

Best Heated Stainless Steel Mug Car Coffee Cup With Charger Deals

Heated Stainless Steel Mug Car Coffee Cup With Charger
Customer Ratings: 2.5 stars
List Price: $14.95
Sale Price: $10.35
Today's Bonus: 31% Off
Buy Now

I bought this mug to replace a similar item that had stopped heating. The new mug looks the same on the outside, but the interior is plastic rather than stainless steel. The visible plastic rim should have tipped me off, but I wouldn't have thought it could turn out this bad. It heats up just fine, but when it does, my coffee tastes more like plastic than like coffee. I tried washing it a couple times and heating up some soapy water in it, but the plastic taste remains. Keep searching until you find a heated mug that you can confirm has a non-plastic interior.

Click Here For Most Helpful Customer Reviews >>

This heated car mug worked well for a couple of weeks, but then the connection between the mug and a wire stopped working. Something wrong with the connecting parts. It just does not stay connected. The connection between the wire and a car (sigarett outlet) works well. But it does not help much, because the wire does not connect to the mug, so it does not do the intended job. My coffe is cold.

Best Deals on Heated Stainless Steel Mug Car Coffee Cup With Charger

When I first bought this mug, I heated water in it to test it. It heated the water just fine but it smelled AWFUL kinda' like a tire. I've been filling the mug repeatedly with boiling water and it's getting better. I'm looking forward to using the mug soon when the smell is completely leeched out. However, I would strongly recommend you just buy a different mug and spare yourself the effort.

Honest reviews on Heated Stainless Steel Mug Car Coffee Cup With Charger

This the second time I have purchased this item.

The first one worked until water got in the inside of the shell. While I am not sure whether or not someone put it in the dishwater (probably a no no) the fact is that I was using the cup plugged in with my left arm on the open window frame of my car and when the cup touch my lip I recieved a shock to my arm.

Trashed that one and bought the second one 2 weeks ago.

This one must have a faulty thermostat because the outer shell gets too hot to touch.

Also, the electrical conection in the handle has broken free making it very difficult to attach the plug.

Don't think I'll try for #3.

Find helpful customer reviews and review ratings for Heated Stainless Steel Mug Car Coffee Cup With Charger

mug gets way too hot.I think it would boil if it was pluged in and unattended.also bottom of mug gets too hot,poorly insulated.

gets too hot

Buy Fom Amazon Now

Friday, September 12, 2014

Cheap SoleusAir 13,000 BTU Portable Air Conditioner, Dehumidifier

SoleusAir  13,000 BTU Portable Air Conditioner, Dehumidifier, Heater, # LX-130D
Customer Ratings: 3 stars
List Price: $822.00
Sale Price: $441.00
Today's Bonus: 46% Off
Buy Now

We bought this unit 6 months ago to try and cool our 2nd floor (3 rooms). I set the unit to 70 degrees and it would constantly freeze up (meaning, ice would form after about 1 hour). I noticed that the unit drew more air in than it blew into the room. Giving the unit the benefit, I sealed everything in the room as tight as I could (insulating, foaming, etc) and closed off the other 2 rooms. It managed to cool that one room (12 x 16) but still would ice over on days of 100+ degrees (unit set for 70 degrees).

Heat pump: I turned it on in mid October. Today (December 10th), all of the lights on the front panel were blinking on and off and the unit would not turn off using the control panel power button. I unplugged it from the wall and left it sit for an hour. Plugging it back in (an hour later), the unit would run but all of the lights were flashing on and off with no control over the power.I am awaiting customer service to contact me to see how they will react to the 1 year warranty. I will try to post what has happened to keep consumers informed.

Click Here For Most Helpful Customer Reviews >>

This rather expensive portable air conditioner is of very low quality, and it's also very poorly designed.

First of all, the air conditioner leaks water from the base. I purchased one, it leaked, I returned it, and the replacement leaked as well.

In order for a portable air conditioner to work properly, it needs to have a two hose design so that one hose takes in outside air to cool the compressor and the second hose expels the hot air from the unit to outside your house. This air conditioner only has one hose that vents the hot exhaust through a window to the outside of your house. This mean it takes in cool air from inside your house and blows it outside to cool the compressor. This creates a partial vacuum inside the house, which results in warm, humid air being drawn in from the outside to fill the partial vacuum. The intake of warm humid air almost completely offsets the amount of cooling this unit is able to provide. Using this unit alone in one small bedroom, the temperature would often be above 80 degrees F on hot July and August days. That's not acceptable performance for such an expensive air conditioner in such a small room.

For a portable air conditioner to work efficiently, it needs to have two hoses: one for intake and one for exhaust.

Lastly, the compressor and fan on this unit are very very loud. It's difficult to watch to TV or carry on a conversation while the unit is running.

I do not recommend this product to anyone.

Best Deals on SoleusAir 13,000 BTU Portable Air Conditioner, Dehumidifier

I bought this unit two days ago when the temperature in a recreation room (fully insulated, measuring 35' x 17' or 595 square feet. Note: unit is rated for 550 square feet) over my garage reached temperatures of 98 to 100 degrees in this latest heat wave in New Jersey. The reason I purchased the "Soleus Heat Pump Air Conditioner" is because I wanted the duality of an air conditioner and heater.

The set up was not difficult, the window assembly kit that fits in the window had to be cut down, as required in the instructions to fit the window. That took about 5 minutes to measure and cut. Total set up time was about 35 minutes. Of that time twenty minutes were spent trying to understand the directions.

The instructions are not the best. There is a hose for draining water from the unit that is not mentioned anywhere in the instructions. The unit has Control Panel and Digital Display that is easy to use and a Remote Controller. The unit also has a timer and louvers that will oscillate up and down to circulate the air. What is not mentioned in the general instructions but under the Remote instructions is that the timer and oscillator can only be accessed through the Remote. However, none of this is insurmountable. After a few minutes of flipping back and forth between pages it can be figured out.

The venting kit that comes with the unit should have supplied some gasket material to put between the exhaust panel and the window. Luckily I had some sponge rubber gasket to assure a good seal. Also, it is a tight fit between the window sill and exhaust hose that fits into the window kit.

After I had the unit up and running I insulated the flexible PVC exhaust hose as per the instructions. The hose becomes quite warm and the heat from it will radiate back into the room, so insulating it makes sense.

Today as I am writing this, July 22 2011 at 1 pm, it is 101 degrees outside in the shade and very humid. In the room over the garage "Soleus" unit is maintaining a constant 82 degrees with 54 percent humidity. I consider that good, the main part of my home has central air set at 72 degrees and it is struggling to maintain the temperature at 74 degrees.

I consider the "Soleus" unit to be working pretty good for a portable air conditioner with extremely high temperature outside. I expect better results when the temperature gets down to the low 90's where it is more normal for summer here.

Honest reviews on SoleusAir 13,000 BTU Portable Air Conditioner, Dehumidifier

Seems to work adequately as an air conditioner. I thought I might not need to, or want to run our old dehumidifier. I purchased the LX-130D to use in the basement and expected that it would work even better at removing moisture than the old dehumidifier. The old stand alone dehumidifier runs for a fraction of the time to achieve the same level of de-humidification. The air conditioner and heater work well but are not super powerful.

Find helpful customer reviews and review ratings for SoleusAir 13,000 BTU Portable Air Conditioner, Dehumidifier

Bought this unit in spring 2010 and used it for about a year now. I have only used it to cool not heat.

Installation: Unit comes with an adjustable 5" tall PVC vent. I had to cut it down to fit my small window which was not a big chore. After that it was pretty much attach the vent hose and plug it in.

User interface: The buttons on the unit are pretty simple my only gripe (and it is minor)is that the fan speed indicator on the LED is represented by a series of blinking squares and they blink faster and it's not really clear what fan speed your on so I pretty much go by the feel and noise which is good enough.

I don't ever use the remote but i did play with it a couple times and it does not seem to like you using a combination of the controls on the unit and the remote. If i turn on the unit using the power button on the unit instead of the remote power button it wants to ignore the remote. but honestly i haven't used it enough to sort out what the problem is.

COOLING: the unit cools pretty good it doesn't cool quite as well as i hoped it's rated at 12.5 KBTU but I'd say it seems to perform more in par with a really good 10 KBTU machine. It's a little nosier than I hoped but it's not horrible for a unit like this.

WATER DRAINAGE: The best thing I can say for this machine is that is super great at blowing water out with the exhaust and I never have to drain it. When I first got it after a couple days of operating I noticed a puddle on the floor by the plugged drain. So I got really worried I was going to have to be draining this thing constantly which would be a real pain since the drain is only about 3/4" of the floor. However after I took out the plug and drained a little water then put the plug back in it's never leaked or needed draining again. My guess was that the drain plug was just not in good enough and it now evaporates all the water out the vent.

Buy Fom Amazon Now

Thursday, April 17, 2014

Buy Sunpentown SH-1508 Tower Ceramic Heater with Ionizer

SPT SH-1508 Tower Ceramic Heater with Ionizer
Customer Ratings: 3.5 stars
List Price: $98.00
Sale Price: $70.72
Today's Bonus: 28% Off
Buy Now

This is a great unit and just like it states it is wisper quiet. Easy to read digital temp. Took about 5 min to warm a 63 degree room to 72! Takes up little space, I put mine in the corner and you don't even know its there. It is also an attractive unit that I don't mind having in any room of the house. The remote controol is a plus also. I Did not think I needed it, but now that I have it, I love that feature also. There is an easy to use timer on the unit also. That is a nice feature so you don't forget to turn it off when you go to work etc. I am thinking about ordering another one as this is such a handy unit. With heating costs this winter it is a money saver to use this electric unit to supplement your heat.

Click Here For Most Helpful Customer Reviews >>

I bought this heater for my living room. I have central heat and air, but this helps me save money on my heating bill. It's slightly more expensive than other ceramic heaters, but it has an air purifier and a remote control. None of the cheaper ceramic heaters have those features. You don't realize how handy the remote control is unless you have owned an electric heater without one. You can make minor adjustments to its thermostat with the remote control. You can adjust the thermostat from 64 to 90 degrees. It has a big, bright LCD display on the front that shows the temperature and other information. Many people seem to prefer those electric oil-filled heaters, but some of them can take forever to heat up a room. This heater produces a lot of heat quickly. It's rated at 5,200 BTUs. A small air conditioner has a rating of about 10,000 BTUs. It also has the ability to automatically alternate between high and low power when it's in AUTO mode. It doesn't always use 1500 watts of electricity because of that. Sometimes it will only use 950 watts if a room is already warm. The Sunpentown SH-1508 is the best electric heater I have ever owned.

Best Deals on Sunpentown SH-1508 Tower Ceramic Heater with Ionizer

SPT SH-1508 Tower Ceramic Heater with Ionizer

I would have to give this rating a one star unfortunately. THe heater while in itself is a great cost you must be warned of the manufacturing of the product itself. I have two of these heaters purchased within a few weeks of each other. One worked well, we were so pleased that we ordered another (my roomies and myself) unfortunately the first one came broken, making a horrible clicking sound and the company (SPT)has refused to help. Amazon did send a replacement for the first and then the second one arrived making an horrible buzzing noise. Amazon was not willing to replace this one. Today is the 8th week of owning both the heaters. THe first one's face plate caught fire today because of poor wiring used in the assembly of the heater, and the second one I am afraid will do the same. This product almost set fire to my house and everything that we own.

I cannot reccomend this product to anyone. Although the price is fine (money wise) is it really worth risking far much more than sixty something dollars if it costs you your life? I do not think so. I am so upset by this that I will write to amazon.com today strongly recommending that this product be removed from their site. Because if three products have thus far been malfunctioning who knows how many more of these are out there will similar situations. So far I have found over 200 similar stories about this product. Thank you for your time and I wish you the best of luck in finding whateever it may be that you are looking for.

Happy Holidays everyone.

Honest reviews on Sunpentown SH-1508 Tower Ceramic Heater with Ionizer

This machine is larger than many ceramic models but nice looking and heats very well. The fan is very quiet. I like that you can use it as a fan without heat as well. My only complaint is that the blue LCD that tells the temperature does not dim or shut off and is VERY bright. Too bright for a bedroom. Really lights it up. I'll be looking for some way of safely masking it. Otherwise very nice but hope it lasts.

OCTOBER 08' UPDATE:

2 California coastal winters (mild and short) and it's dead. Well not dead, but working erratically (noisy, not shutting off when the room reaches the Auto shut off temp, ...) No longer safe or usable.

For the bright light, I masked it with electrical tape. Safe and effective.

Find helpful customer reviews and review ratings for Sunpentown SH-1508 Tower Ceramic Heater with Ionizer

After reading dozens of reviews on dozens of heaters, I gave up and ordered what looked good. So far, I very happy with this one. Although assembly was indicated, it came fully assembled. It heats my son's bedroom (10 x 12) in very short order and it takes the chill off my living room (16 x 22). I switched to a pellet heater as my primary fuel and there are some areas of my home that just stay cool. I'm confident this will do the job on all but the coldest of days (Mid-Michigan). The directions are easy to understand and the remote is simple to use. The only drawback is the LED panel is super bright for my sleeping preference (great nightlight for a kid) and when the timer (max 7.5 hour) shuts the unit off, it seems to erase the preset room temp. It then defaults back to 75 degrees. Could be I haven't figured it out yet but either way, that's a minor thing to me. Overall, I think I got a good deal on a good heater.

Buy Fom Amazon Now

Sunday, April 13, 2014

Reviews of Optimus H-9010 Garage/Shop Ceiling or Wall Mount Utility Heater

Optimus H-9010 Garage/Shop Ceiling or Wall Mount Utility Heater
Customer Ratings: 4 stars
Buy Now
I purchased this heater because I had good experiences with a Marvin infrared heater of similar design and capacity. The Marvin failed after many years of dependable service, and since they are no longer in business I choose this Optimus brand.

I purchased my first Optimus H-9010 about a month ago, and have been so pleased with it that I purchased a second one which I installed yesterday. Here are my impressions:

o The stated specification of 600/1200 Watts is incorrect or has been changed. My heaters are clearly labeled as being 750 / 1500 watts, and testing with an amp meter confirms this is about right as it draws 6.3 / 12.3 amps.

o The installation is easy and convenient, the mounting bracket is long enough to straddle two studs spaced 24 on center. Mounting bolts are included.

o Once mounted, the heater can be rotated through 90 degrees that is tilted 45 degrees off vertical each way.

o Build quality seems good, about the same as my original Marvin heater. Indeed, aside from the addition of the light, this Optimus seems to be the same design as the Marvin.

o The unit needs to burn off a bit of factory residue, and it will stink a bit for the first 30 minutes of run time. After this period it runs clean with no smells or odors whatsoever.

o The cord is a generous 82 inches. If you must use an extension cord, make sure it is at least 14 gauge and as short as possible.

o The switch, activated by tugging on the convenient cord, has the following modes:

(0)-Off

(I)-Lamp On

(II)-one quartz element glows (750 Watts) & Lamp On

(III)-both quartz elements glow (1500 Watts) & Lamp On

o The light is a 25 Watt Halogen bulb with a G9 base. It swivels in up-down and left-right so it can be aimed where you want it. Of course this is too tiny a lamp to be used by itself for any serious work, but it never hurts to have extra light in ones shop. I like it, and I don't mind that it is always on while the heat is on, but if it's a problem I guess one could just remove the bulb.

o Operation of the unit is completely silent, with the exception that there are some slight noises as it begins to warm up (due to metal expanding, I presume).

o There is no built in thermostat, the unit is either on or off which is probably adequate for most folks. I rigged up a wall mounted thermostat that powers a ceiling socket, so I can set the heat to any desired temperature (typically about 55-60 degrees), and have found this quite convenient as I can turn down the heat when I'm not in the shop (to about 40) but still ensure that it will not freeze.

o This ceiling mounted heater seems very safe in a dusty environment such as a woodworking shop, because it points down, keeping the red hot rods clean and dust free. In about 5 years of use (with my original Marvin heater) I never had any safety issues, even though I occasionally allow some heavy dust to accumulate on the top of the unit.

o Another nice effect of these ceiling heaters is that when I have glue-ups or finishing jobs I can place them on the bench directly under the heater and they will cure faster than if place off in a colder corner.

As stated in the title, I use this heater in my woodworking shop, which is actually a converted double garage, about 680 square feet in size, located in the Southern Interior of BC Canada. It is insulated, with a wood floor over the concrete slab. The automatic garage doors, which leaked a lot of air and heat, have been removed and walled in. Before I removed the automatic garage doors and covered the cement floor with wood, I was able to keep things from freezing with just a single 1500 Watt infrared heater in fact I was usually able to keep the shop at 50 degrees or better if I allowed the heater to run long enough.

If a single heater was sufficient for my original cement floored shop, you may be wondering why I need two heaters after I've added a cozy wood floor and improved the insulation. It is so that I can better spread the heat around (by running each on half power 750 watts), and also because I can run them both full blast for the first half hour or so to bring the shop up to a comfortable temperature faster (about twice as fast, in fact).

A quick word about comparing heaters to each other. Virtually all electric heaters produce an identical amount of heat per watt. So, in the long run, any 1500 Watt heater, say a fan based unit, will make a room as warm as any infrared heater that is also 1500 watts. The difference lies in what gets warmed up first. A fan based heater first heats the air, and the air then heats the stuff in your shop, including you. The infrared first heats the stuff it's pointing at, which then eventually heats the air. If it's pointing at you, well you feel warm right away, but if it's not, then you don't feel much warmth until the whole room is warm.

If you are comparing this heater to non-electric units, it's best to compare BTUs. This one puts out about 5,000 BTUs.

Hope this was useful.

Click Here For Most Helpful Customer Reviews >>

THIS THING ROCKS!

I absolutely love this heater. I've had it for quite some time now and it puts out a good amount of warmth in my garage.

No, it doesn't make the entire garage an 80º paradise on freezing winter nights, but it does help, and quite a bit. I installed it just above and behind my work bench area and in just a few minutes I can feel the air get noticeably warmer.

WELL worth the money. Would recommend to anyone who works in the garage on cold days/nights.

It installs easily, too.

Best Deals on Optimus H-9010 Garage/Shop Ceiling or Wall Mount Utility Heater

It took over 2 weeks for my order to ship so be warned that if you order this item it won't be received for around 3 weeks. It's identical to other heaters which have a different brand name, and it's cheaper but you have to hunt for it by looking for the Optimus heater and then click on the cheaper price which comes up unless you want to pay around $70. I got mine for $46.

The mounting bracket is pure crap; a soup can is made of stouter steel. Thankfully the heater unit is very light and long, sturdy screws are included for screwing into wall or ceiling studs. There's a fair bit of heat which escapes from the slits in the housing on the top of the unit which ends up hitting the ceiling. Your ceiling will get warm but not HOT.

Like others have done, I didn't really need the halogen light in the unit so I removed the bulbs. I wonder how much cheaper the heater would be without including the light.

Honest reviews on Optimus H-9010 Garage/Shop Ceiling or Wall Mount Utility Heater

I hung this near my bathroom shower and it is great on those chilly mornings. And you can also install it on it on a timer. Come w/2 speeds and a light. I recommend this seller and this product.

Find helpful customer reviews and review ratings for Optimus H-9010 Garage/Shop Ceiling or Wall Mount Utility Heater

i had two heater similar like this and the heat is much stronger than this unit. very disappointed even with the high setting

Buy Fom Amazon Now

Wednesday, April 9, 2014

Reviews of Candle Wax Warmer: Scentsy ABCs Mid-Size Scentsy Warmer PREMIUM

Candle Wax Warmer: Scentsy ABCs Mid-Size Scentsy Warmer PREMIUM 'The Best Teachers Teach from the Heart'
Customer Ratings: 4 stars
Buy Now
The design is cute, I absolutely love it! Definitely a great gift for teachers or anyone else really. This product works well with other Scentsy bars. Recommended.

Click Here For Most Helpful Customer Reviews >>

This is the perfect Scentsy teacher gift. This warmer and a scentsy bar is the best gift you could give a teacher as an end of the year gift, xmas gift or even valentines day gift. It's perfect.

Best Deals on Candle Wax Warmer: Scentsy ABCs Mid-Size Scentsy Warmer PREMIUM

I asked to cancel the order when I finally received the confirmation that it was being sent. I knew I wouldn't receive it before the last day of school. It was for my daughters teacher for her end of year gift. She told me that it was too late to cancel since it was already in the mail. I understand that, however I needed it and didn't receive it until several days after. It looks nice sitting in its box on the counter.

Buy Fom Amazon Now

Monday, March 17, 2014

Cheap Sunbeam Ceramic Heater

Sunbeam Ceramic Heater
Customer Ratings: 2.5 stars
Buy Now
Bought at Walmart for $30 in February as a little heater to warm up my wife's craft room since its a back bedroom and we only open to receive heat from the rest of the house when she is working in it. However, I will be taking this heater back. The heater is a handsome little unit: 10" tall, 14" wide, and 8" deep. It sits on a 7"x9" base that makes the unit very stable and resistant to tipping over from accidental bumping. The base allows 360 degree rotation and about 15 degree tilting. The heater's operating modes (per the manual) are: Fan Only, Low Heat ("if applicable..." said the manual. This unit did have Low Heat mode.),Eco-Smart, Max Heat, and Thermostat Control. Max Heat runs continuously at 1500 watts. Low Heat (if it were available) would run continuously at 750 watts. Eco-Smart "cycles between High Heat (1500 watts) and Low Heat (750 watts) settings...". Thermostat Control only has four room-temperature settings: 70, 75, 80, and 85 degrees. The extreem left of the thermostat scale has a "Frost Protect" setting (thermostat control set for 40 degrees). The extreem right of the thermostat scale is "Constant On". While the front of the heater presents a good sized 8"x14" grill, it is for looks only the actual heat producing opening is only 2"x6". The remainder of the area behind the grill is just black plastic. When the heater is on and at 6" from the front of the heater, you feel VERY hot air at 18" from the front you feel no hot air. This is my first point about the poor functionality of this unit: the output of the internal fan is so pathetic that it can barely produce enough of a wheeze of air to get the heat only a few inches out of the heater and then (hot air rising) goes straight to the ceiling. Perhaps this is a general trait of all ceramic heaters: they can produce very hot air without using red-hot (read: accidental ignition source) heat elements; however, they cannot support large volumes of air being passed through them. Here is my second point on the poor functionality of this heater: Although the box advertises: "High/Low Heat Settings" the low setting is not actually selectable. The unit seems to run at a high heat output all the time I did not discern any "cycling" between a high and low heat output in the lame "Eco-Smart" mode. The third point is the thermostat control: only four choices: 70,75,80, and 85 nothing inbetween and nothing below 70 degrees room temp is available, and it seems to operate at max heat when in thermostat mode. Dear Sunbeam, What I wanted to know about a heater is: the heat wattage of the settings, the operating range of the thermostat, and can the low heat only setting be selected for thermostat control. You're packaging told me absouluty nothing about the details and specifications of a heater that are actually important. Oh, by the way, people are tired of, and turned off, by manufacturers who trot out the same mediocre, half-hearted designed products but think that by putting a green leaf on the box and use the word "eco-" that consumers will think that the products received an improvement of some sort.

Click Here For Most Helpful Customer Reviews >>

This heater is a great idea, and the functions work great. It is one of the best space heaters I have owned with one major exception. I think they undersized the wiring on it, because the power cord gets very hot, and I'm afraid it will catch fire. It actually melted my Kill-A-Watt power meter I had it plugged into. I wouldn't buy this item. It does heat very nicely, but it is a fire hazard in my opinion. Made in China...

Best Deals on Sunbeam Ceramic Heater

In less than a month the heater not only just quit working, but a wire inside melted when fortunately I was at home. I opened the machine and there it was, the burnt wire. It could have burned down my house

Honest reviews on Sunbeam Ceramic Heater

This heater started out heating a small bathroom and washroom quite well.Like other products I have purchased I bought before looking at reviews.After 30 days the heater started to blow cold air.At this point I looked up the reviews and saw where mine wasn't the only one that has done this.Rather than to take it back and let them throw it away and not do anything about it I decided to take the heater apart and see what was causing the problem..If costing me $30 keeps one house from burning down it has made the loss profitable. There are 3 wires leading to the heating elements 2 red and 1 black in the middle.The black wire in the middle had been hot and melted the plastic cover on the wires and had burnt in two.I have pictures but cant upload them here.Just another Chinese piece of DANGEROUS JUNK.

Find helpful customer reviews and review ratings for Sunbeam Ceramic Heater

We've had this about a year. Have not had any issues and we use it every day; placed near where we sit. However, when used in a bedroom sized space (our office) and keeping the door closed, it heats up the area quite nicely and soon we turn it off when it reaches a heated comfort level for us. However, due to reviews about a burned wire, I will be more careful in how long I let it run and I do always turn it off and unplug it when I leave the space.

Buy Fom Amazon Now

Saturday, March 15, 2014

Review of Dyson AM05 Hot + Cool Fan Heater

Dyson AM05 Hot + Cool Fan Heater
Customer Ratings: 4 stars
Buy Now
Customer review from the Amazon Vine Program

I have been intrigued with the Dyson Hot + Cool Fan Heater for a few years. I remember checking one out at a big box housewares store and was just thinking how interesting the design was but equally amazed at how high the price was. The design was certainlly clever and modern but it was not clear to me whether the performance could equal the expecatation and cost. I finally have a Dyson Hot + Cool thanks to the Amazon Vine program and I've been putting it through some serious testing and usage. My video review will cover most of my thoughts but I"ll highlight some of my thoughts here. After using it for nearly a year in both cold and hot conditions I am able to say it is NOT very effective as a fan and marginally more effective as a heater.

Let me be clear about one thing, the device name is totally misleading. It is called "Hot + Cool Fan Heater". It is NOT a cooler. It does not cool air whatsoever. An air conditioner cools air. This is not an air conditioner... it is a fan and it is not very effective as a fan because the air flow is simply too weak to be effective. Additionally it is very loud during operation.

I do like the look of this heater/fan. It's very modern and futuristic. Its slim design will enable it to be put in some otherwise tight spaces and will also look quite modern and elicit many comments, I'm sure.

The actual performance is poor. As a heater, it works pretty well, but only in a smaller square foot area. Since the head can oscillate back and forth, it sill distribute a warm flow of air fairly effectively in smaller rooms. Normally the thermostat in my house is set to 62 degrees during the overnight. I set the Dyson Hot + Cool downstairs in the living room. The entire downstairs area is approx. 900 sq feet but but has a relatively open floor plan so about 3/4 of that square footage could essentially be considered one room. The Dyson managed to keep the temperature right aroun 68 degrees all night long. The Dyson temperature had been set to 70 and as far as I know, it never attained 70 degrees. I'm pretty sure it ran continously all night long. I thought that being able to maintain a 68 degree temperature in that size space was pretty good though since it's still winter where I live and if the heater had not been on, it would have dropped to 62 degrees inside. If a smaller room were being used, it would heat the room to a higher temperature.

As a "cooling" fan, I was not impressed. There is simply not enough velocity or volume of air to be very effective as a fan. Not only that, but the Dyson is loud especially when the fan is operating at its highest setting. At the low setting it's not that loud, but then it's much less effective too. So to get a significant fan effect, you have to turn the speed up to a level much higher than "low."

I do like that the fan oscillates and also tilts. Howver, in my use of the fan, there was a significant amount of wobble in the head of the unit when it was tilted and oscillating. In fact at one point the unit almost vibrated or wobbled itself off the edge of the counter it was sitting on while I was out of the room. I could not believe my eyes. When the head is straight up with no forward or backward inclination, it's fine.

The remote is useful and magnetically attaches itself to the top of the head when not in use. But in my video you will notice at one point the remote slides off the top when I tilt the unit so the magnet is not as strong as it should be to hold the remote securely.

If you are a design forward kind of person or just admire the "genius" of Dyson, this fan will probably appeal to you. It's more flash than function in my opinion. If you're thinking that for the price it's got to be one incredibly effective fan and heater, you'd be mistaken. For the price, it's one awesome looking piece of equipment, but performance is not so hot (no pun intended.)

For my money, I"d rather buy a seperate floor standing fan, or box fan, that can really push some air and at significantly less cost. The Dyson can't even compare.

As a heater, it's pretty cool (sorry again, no pun intended) but again, expensive. I have a small, square, ceramic heater that is very quiet and effective. I think it cost around $40-50.

One worry I have and that I can't address until I've used this for a much longer time, is how much dust will collect in the air intake holes on the lower section of the unit. I've had other devices with similar looking holes and over time you get this very fine and hard to remove collection of dust buildup that would also reduce air flow. Internally dust might build up somewhere too. I have no idea how that would affect the already mediocre performance... or how to clean it. And the air output venturi would also collect dust over time and have to be cleaned.

I guess the Dyson and me aren't a good fit. It's cool looking as heck but I just don't think it lives up to my expectations of performance for something that costs this much. I can see this fitting in to certain decors really well though. And its slim design does enable it to fit in what would otherwise be tight spaces for other more conventional fans/heaters.

UPDATE: 6/3/2013 Having used this over the winter and now during some really hot weather, I'm reducing my rating to 2-stars. For the price, this just doesn't provide a commensurate level of performance. I would not recommend unless you just want to make a fashion statement but don't really care so much about effective cooling or rock-solid mechanical performance.

Click Here For Most Helpful Customer Reviews >>

There are so many reasons why I love the Dyson Hot + Cool Fan Heater:

1. I am saving $300 per month on heating because the coldest member of the household is now warm enough and not using the whole house forced air heater to cook everyone.

2. It warms up a 15' x 15' bedroom fast about 90 seconds fast.

3. The cats and dogs and children never get near any moving parts that might injure them there are no moving parts.

4. There is no risk to anyone touching the heater it does not get hot to the touch.

5. It is quiet on low it is silent on high it is barely audible.

6. It is working all day and all night everyday for 8 months and has not crapped out.

7. It looks terrific. I redecorated and the style and beauty of the device adds to the modern design.

8. The remote control works perfectly.

9. It is enduring some rough handling amongst family members and guests and pets without busting.

10. It will get the room as warm as anyone wants to get the room. If someone doesn't feel well and wants it at 90F then it will deliver.

11. The animals are not afraid of it.

This is the best three hundred bucks I spent in the past six months. I am overjoyed that I took a chance and purchased this awesome heater despite the negative reviews. We are enjoying this heater, benefiting from this heater and I still love to marvel at its elegant engineering innovative design. So happy. Seriously pleased.

12. It's July and I have to add this fan cools. I don't understand how it blows cool air on a hot day but it does. There is no cooling component but the air from the Dyson is at least 10 degrees (F) than the rest of the room. Very refreshing.

8 months of daily use and we LOVE the dyson. And it looks great. I give it a wipe every so often because the air inputs attract dust. That's it for maintenance. I would love more well engineered products. It saved our household a lot of money during the winter. I will take a look at the heating bills one day and share how much. I really don't like many products, and I don't review most what I purchase. I haven't found a flaw yet.

Best Deals on Dyson AM05 Hot + Cool Fan Heater

Customer review from the Amazon Vine Program I'll give it to Dyson... They've taken a very boring household appliance and made it sexy and cool. The design of the AM05 is super slick, elegant and very futuristic. But at $400, a cool design is not enough; to justify the price point it needs to drastically outperform standard fans and space heat by orders of magnitude. Sadly, it doesn't even come close. The packaging is quite minimal and the only assembly required is to pop the fan in the base which takes a few seconds.

On the design... For such a sexy form factor, I do not know why on earth they would have a black electrical cord for the white/silver fan... I would be willing to bet that everyone that chooses the white/silver fan would prefer a white or grey electrical cord.

On the performance... The "cool mode" simply blows air and doesn't actually cool. The product description and product packaging are incredibly vague (I suspect intentionally) about what the cooling function actually is. After using it for a while, I didn't notice it actually cooling the air at all, so I decided to run a test. I measured the temperature in my room with a precise thermometer. I then put the Dyson in "cool mode" blowing air directly onto the thermometer from around 2 feet away. The temperature did not changenot even by a fraction of a degree.

The fan has 10 wind speed settings1 being the lowest and 10 being the highest. When set to 10, I find the fan quite loud actually. That is, loud compared to my $45 Lasko Pedestal Fan (that also oscillates and came with a remote!). Also, compared to my Lasko the Dyson wind power is significantly less. The Dyson at 10 is comparable to Lasko at medium. The Dyson also has a much smaller "wind target region" compared to the Lasko which is less effective. The oscillation function works well and the fan can be tilted up or down. Note, the magnetic remote usually falls off when tilting in either directiona slight annoyance and a detail you would expect to be covered given the price of the fan. If you like cool yourself in bed, you'll likely need to place it on a small table as it is too short to reach a bed, even when tilted.

In "heat mode," I did notice a slight burning smell on first use, but it quickly went away and did not return on subsequent uses. The heating works quite well and in a test, it brought the temperate of my bedroom from 62 degrees to 72 degrees in around 20 minutes when set to 10 and with oscillation turned on. In my living room, the "heat mode" consistently blew my fuse when used while watching the television (it didn't in cool mode though).

Overall, this Dyson is less performant than both fans and heaters that can cost less than $50. Unless money isn't an issue and you care more about the visual appeal of the fan than how well it works, this just isn't a good buy.

Honest reviews on Dyson AM05 Hot + Cool Fan Heater

I'm a fan of Dyson, but not of the Dyson fan.

In simple terms, it is WAY too noisy, to the point that I no longer use it, and therefore have wasted my $300+.... so disappointing for a Dyson product to be so poorly designed.

Find helpful customer reviews and review ratings for Dyson AM05 Hot + Cool Fan Heater

Customer review from the Amazon Vine Program SEE BELOW FOR UPDATES

We currently live in a spacious one-floor apartment in the outskirts of Chicago. As of now, it's the tail end of winter here, but, as we've only been in the apartment less than a year, this was our first winter in the new pad. The apartment itself is great, but it's in a very old building with very little updates throughout the years.

The room in which I keep my office is one of those updates, as it seems it's an addition. As such, it doesn't have heating in there, so it can get very cold at times, especially when my wife closes the door during the day. I like to stay up at night on my computer or reading in there, so having the cold doesn't help.

Okay, so on to the heater. When I had the opportunity to order this heater, I jumped on it without hesitation, knowing exactly where I'll be using it. My wife bought a Dyson vacuum, and I like the design of it, though I think it's clunky. So the fan/heater was something to which I greatly looked forward.

When it arrived, the box was very simplistically designed and easy to remove the heater from. You only really have to assemble the base onto it, and that's it. Batteries are included, and the heavy-duty cord is more than long enough for my use. The instructions aren't really necessary, as you can figure out how to operate it from the get-go. The only two things I took away from them were that I can tilt the fan itself to have it pointing down or up, and that upon turning it on I have to wait for it to complete a cycle to figure out the temperature of the room. That's it.

At first use, I wasn't thoroughly impressed with it. I thought it would remain constantly on, though I've figured out later that it sets itself at the room temperature, much like an A/C. Since I really wanted it to aim at my feet, which get the coldest, I was disappointed as my feet were still slightly cold, especially when the heater went idle. But then I messed around with it.

The included remote (which can attach itself to the unit via magnets) is spot on the controls on the unit itself. There's the on button, oscillation, power level, and temperature. The stronger the power, the more it'll blow out, useful if you have it in a bigger room. Upon raising the temperature and the power level, as well as tilting it lower, I was able to get how I wanted it the next night, and my feet were great, let alone the rest of my body and room. Oh, and silly me left the door to the rest of the apartment open, which didn't help control the temperature within my office. Thanks to my wife for pointing out that glaring flaw.

In the end, I am pretty happy with the Dyson heater/cooler. The only real issue I have is with the price. I told my wife I was going to give it four stars, docking one for the price. I feel like the price should be around $150, honestly. But I don't know all that goes into making a device like this, as well as the included features. My wife agreed, but explained that Dyson is a higher-end brand; once she saw the magnetized remote, however, she said I should give it five stars--she thought it was the coolest thing ever. Oh, her...

It's great, and I'm glad I can finally stay comfortable in my office in late winter nights.

***UPDATE 03/03/13***

After a little less than a week of using this product, I'm afraid I have to change my review. I'm not sure if I received a faulty product or what, but I will contact Dyson for support in any case. I tried looking up support on their website, but since this specific model is still very nascent in the public world, there was no help I could find for AM05.

As you read before my update, I use this fan/heater for my office in the back of my apartment, which gets really cold in the winter. As of this writing, it's 20F outside. Since there is no heating in my office, I cannot imagine it is warmer than 77F--the temperature at which my Dyson is set, and it's not running at all. After the second day of use, I noticed that my heater didn't start at the last temperature at which I had it. "Okay," thought I, "it may be that it's a bit warmer tonight." I raised it a few notches and...nothing. I initially had it at 65F the first couple nights, and by the third night it didn't start warming up till I had it at 75F.

So the next couple nights were the same, and I tried unplugging and plugging the thing, which didn't do any help. The unit doesn't start working unless I raise it more, and right now it's at 77F and it's still idle. "Is it really 77 in here?" I asked my wife. "No, that's impossible," she replied. "It's freezing in here."

So, I will contact Dyson and update as needed. It's a shame, because when the unit *is* working, it's awesome.

***UPDATE 03/08/13***

Dyson sure enough emailed me back, and they requested I mail them the product I have for a replacement or repair.

I'll update again when I get another or my current one fixed.

***UPDATE 05/16/13***

I finally had a chance to send my "defective" product, and promptly received a replacement.

So far so good. The one I have now seems to be fine, and has read the temperature sort of accurately. Though it's now much warmer out here in Chicago (70Fs), I'll be updating this review at the end of the year once it gets colder again and I can properly utilize the heating feature.

The cooling fan is fine, though you have to set it really low for it to switch to blue. It's able to blow enough cool air into my little office to the point where I'm comfortable without cranking the A/C. (Though I really don't need to do that yet as it's not immensely hot out for now.)

Buy Fom Amazon Now

Friday, March 7, 2014

Classic Flame 33 in. Electric Fireplace Insert with Backlit Display Reviews

Classic Flame 33EF023GRA INSERT ONLY.  Fixed Front 33' Insert w/Backlit Display, with Remote
Customer Ratings: 5 stars
List Price: $669.99
Sale Price: $479.49
Today's Bonus: 28% Off
Buy Now

Easy to install, looks great, best price around. Arrived in great shape. Very happy :)

Love the timer function and gives just enough heat to take the chill out. I would buy this again if I needed a second one.

Click Here For Most Helpful Customer Reviews >>

Monday, February 10, 2014

Review of Sunpentown Tower Ceramic Heater with Ionizer SH-1508

Sunpentown Tower Ceramic Heater with Ionizer SH-1508
Customer Ratings: 4.5 stars
Buy Now
I recently purchased this item but was hesitant on reviews from others. Needless to say Im glad I bought this one. Heat is awesome, thermostat is accurate and its fairly quite compared to others I have tried. All in all this heater has done what others couldn't do which is heat my living room taking the chill out of the air. And from were Im from it goes to -40c. Good job Sunpentown and I even ordered another one for the basement, just a different model.

Click Here For Most Helpful Customer Reviews >>

Heats up quickly. Use it downstairs and it warms up the top rooms. The filter does pull out dust and stuff in the air. I bought it because I have asthma. Price was better than the home improvement stores.

Best Deals on Sunpentown Tower Ceramic Heater with Ionizer SH-1508

This item works really good, it is a little difficult to program, the manufacturer did contact with the info needed to run this device. Cleans the air and has very good heating.

Honest reviews on Sunpentown Tower Ceramic Heater with Ionizer SH-1508

i bought this product to save money on my gas bill, that was achieved. i fell in love with this heater because of the timer and how quickly it starts to heat the room. my last heater took a while for it to get warm itself before the air came out hot. this heater is helping me out a lot, especially after we just faced Blizzard Nemo.

Find helpful customer reviews and review ratings for Sunpentown Tower Ceramic Heater with Ionizer SH-1508

The heater worked great the first month; however, now it randomly turns off and have to completely power down and let it sit a few minutes and then restart it. It's as if there's a fuse or breaker inside that triggers and needs to reset. It is in a well-ventilated area that is not warm with full power. Just does not hold up to the winter....

Buy Fom Amazon Now

Saturday, November 30, 2013

Review of GE 15318 Push Button In-Wall Digital Countdown Timer

GE 15318 Push Button In-Wall Digital Countdown Timer
Customer Ratings: 5 stars
List Price: $29.99
Sale Price: $22.86
Today's Bonus: 24% Off
Buy Now

The product was very easy to install. It's fairly large, so it fit a little snugly into the electrical box. It looks really neat once installed. The LED's are not intuitive though. They blink even when the fan or lights are off. To stop this, switch the fan off with the large button. The LED's will continue to blink, but then press and hold the large button for 3-5 seconds until the fan comes on, then turn off with the large button again. The LED's won't flash until the next time one of the smaller, timer buttons are used. The instructions are not very helpful with describing this override. In a dark room the LED flashing is annoying. I would have given 5 stars if it weren't for the LED issue.

Click Here For Most Helpful Customer Reviews >>

I installed this to control a whole house fan that we have. If you already have a switch in the wall, this easily replaces it. Very easy install and very easy to use and looks nicer than the knob style timer switches

Best Deals on GE 15318 Push Button In-Wall Digital Countdown Timer

This is one of the few timers that has a range from 5 minutes to 4 hours. That's perfect for a bathroom timer whether for an embarrassing whiff, or you want it to completely dry out after a long shower. It's convenient to be able to start the time of your choice with a simple press of a button.

Installation was a breeze. I saw a comment about how deeply inset this product was. It fit snugly, but there was no problem or need to buy any additional hardware to accomodate it. I saw some comments about the blue LED light being bothersome. I don't mind it at all. Mine is being used in a bathroom, and not next to my face in a bedroom. Note also that this timer is not a precision clock. "Four hours" turned out to be more like four hours and twenty minutes. Again, that's just fine for my goals.

Now that I've tried it out, I'm ordering a second one.

Honest reviews on GE 15318 Push Button In-Wall Digital Countdown Timer

I was having a tough time finding a timer, that didn't need a neutral in the switchbox, for my new bathroom fan that takes very little power. This one even works if you have LED lighting or new low power fans. It works perfectly.

It takes about a minute to charge after you turn the power back on after installing, then it's easy to operate. Press the button for the time period you want and the fan starts. A blue LED blinks every few seconds to indicate which time has been selected. If the fan is running press the big unmarked button to stop. If the fan has already stopped press the large button to recall the last countdown period and start the fan. Pretty simple, yet very functional.

I cut one star for being so ugly!

Find helpful customer reviews and review ratings for GE 15318 Push Button In-Wall Digital Countdown Timer

Installed this in our bathrooms and our laundry room. The timer looks great with our existing switches, and the times that are available give a wide range of options. The only complaint I have is that the indicator light only flashes briefly every twenty seconds, and even then it only indicate the button that was selected, so there's no real way of knowing how long is left on the cycle.

Buy Fom Amazon Now