List Price: $80.73
Sale Price: $80.58
Today's Bonus: $0.15 Off
a great value for so many tasks! Easy to use, plenty of air or heat or both and enough light to see fine by alone. I had one ruined by filthy tenants and by buying this unit here it was less than buying just the defective heaterI just popped out the modular components and replaced all without any ceiling or plaster work as the housing was identicala nice quality addition. Quiet, good mist clearing, and toastywhat more could you ask? Add free shipping from Amazon and sold American!
Click Here For Most Helpful Customer Reviews >>
The vent in our bathroom died recently, so seeing that it was a Nutone 665, I ordered this unit, assuming it would be easy to pull the old one out and replace it with this. Unfortunately, the housing has been redesigned for the worse. The old unit did indeed slide out very easily, leaving its hanger bars in the space above the ceiling. The new unit requires you to attach the hanger bars to the housing before installing it. Furthermore, the old unit had an opening for the power to come into the unit where the connections were light, vent, and heat were made. The new unit has these connections outside the housing.Basically, I had to cut open a larger hole in the ceiling to allow for the hanger bars and give me space to hammer them in. The grille is barely larger than the housing, so now I have an ugly space surrounding the unit in the bathroom ceiling.
If they hadn't changed the design, I could have reconnected the power, slid the unit in, and hung it on the old hanger bars and written a 5-star review. The new design makes it much harder to install in a finished bathroom and I see no reason why it was changed. The old unit's design was far superior. If I fix the drywall and this unit dies, I'll have to cut the ceiling again to get it out. I'd rather just leave the hole and find some kind of frame to fit around the grille to hide the hole.
Best Deals on NuTone 665RP Heat-A-Ventlite 70 CFM Exhaust Fan with 1250-Watt
We had a 25 year old version of the same heat/vent/light which was still, amazingly, working. It was a bear to get down, but once we did, the new one installed easily in the same space. It's much quieter, heats the space more quickly, and looks great -the old one's grill had turned a murky yellow-orange and the light visor was bubbled. It's nice that we could get a similar but improved model that used the same sized hole.Honest reviews on NuTone 665RP Heat-A-Ventlite 70 CFM Exhaust Fan with 1250-Watt
These vent/heat/light fans were installed in my house when it was built over 23 years ago. My exhaust fan motor was rumbling a lot, so I decided to replace it. They have discontinued selling the motor so I had to buy the entire thing. Last time I just had the motors rebuilt by a local small electric motor repair place. I probably should have done that this time as well.This unit is not exactly an exact replacement. I had to cut away a little more ceiling because it was maybe a half inch longer than the original. I have full access to the attic above the fan. If you don't have access to the area above the fan installation location, I'm not sure you will be able to install this.
Biggest problem mounting the unit was the location of the support brackets on the housing. The ceiling is 1/2" sheetrock mounted onto 3/4" ferring boards which attach to the joists. When the bottom of the fan is aligned with the ceiling as per installation instructions, the support bars do not line up with the joists. They line up with the space that the ferring boards create between the joists and the sheetrock I had to mount the housing a little higher and toe-nail the supports into the joists. Only other choice is to attach some support boards onto the joists and extend them down lower to the support bracket height.
The unit comes with a new 'reflector' that accomodates a regular incandescent light bulb. The old unit had a much larger 'reflector' which gave enough room to use a CFL bulb. If you use a regular light bulb, the lens will get a yellow spot burned into it after a few years of use. I've seen this in a lot of houses with this model. So I use a CFL which burns cool and doesn't discolor the lens. In order to use the CFL bulb I just installed my old 'reflector' instead of the one that came with the new unit.
Construction is a liitle cheap, but so is the price, and it works fine. The wire hookup area has a flimsy aluminum shield and you're working with a lot of #12 wires that need to be folded away carefully in a small space or else the aluminum shield will bend and/or won't re-install properly.
It's a little on the noisy side, but it has the heater as well as the exhaust vent. To get a 'quiet' fan the cost is considerably more, especially if you want a heater as well. It's the guest bath so it's not used that much, so it's ok. In the master bath we installed a remotely located fan unit so that you can barely hear it running.
Find helpful customer reviews and review ratings for NuTone 665RP Heat-A-Ventlite 70 CFM Exhaust Fan with 1250-Watt
I bought this one to check it out for a house that we're rehabbingThis one is a bit smaller but still pumps out the heat and has
a decent exhaust fan (4 Sones). There is no night light in itsomething
I will remedy by hooking the light up to a dimmer. Overall this unit
should last as well as my old one It's a tried and true design
and built wellbut in China.
It calls for a dedicated 20A 120V circuit though at 1250 watts
it should run OK on a 15A circuit if not shared with any other big loadsesp a hair dryer.
At the current price it is a bargain for installation from above.
However, I agree with Hari NairAs a retrofit it has a serious design flaw. It
is difficult to install from belowsomething that could have and should have been
accommodated at the design stage. It can made to work by cutting off the
external mounting ears and drilling some holes to screw it directly to the joist
from inside the housing. Then, with a strong and patient person holding it close to the ceiling you can push
the wires through the wiring cover and wire nut them to the various connections. then attach the cover with
its' one screw (too bad the cover doesnt have a keyhole for the screw) and then you and your helper can push the unit through the opening and screw it to the joist.
I know this works because we did it last weekbut it certainly isnt easy.
I have always thought that designers who are too lazy to think about the end user and installer should
be sentenced to installing and repairing their designs for a month. Design Supervisors who tolerate such
laziness should get 2 months.
I'm subtracting a star for Nutones's failure to accommodate retrofit applications.
No comments:
Post a Comment